Processor Re-Furbisher Cleaner ZX-100 Hydra International Corporation Inc The Pinnacle Building, 3455 Peachtree Road NE, Suite 500,  Atlanta GA 30326 Tel: 1-866-809-7286   Fax: 1-866-379-1229  Email: sales@hydra-usa.com   Web Site: www.hydra-usa.com                                                     NEW Fast Acting, Deep Cleaner For Mini-Labs, Professional Film & Paper Processors Non-Fuming ZX-100 Rapidly Removes Heavily Oxidised Developer, Crystallized Fix / Bleach Scale & Soft Sulphur Build-up, From Racks, Hard, Soft Rollers & Tanks.                                                                                                                                                                                              Powerful ZX-100 starts to work on contact.  Rapidly removes the heaviest build-up of chemical contamination without heavy  scrubbing.  Deep cleaning is fast and easy and when used as total processor cleaner greatly improves the working efficiency of your processor by cleaning pipe-work tanks and pumps.  Using ZX-100 stops fresh chemistry from being contaminated by old chemical build-up on racks and tanks.  Also used by Specialized Refurbishment Companies and Service Engineers Remove any soft squeegee top rollers or strips if present before soaking in ZX-100 as very soft rubbers can be effected by deep cleaners.  ZX-100 is safe on hard rubber rollers, soft rollers and socks.  Note: Do Not use Hydra ZX-100 on Acrylics such as  Perspex. To Clean Racks out of processor:  Dilute Hydra ZX-100 at 1:15 with water  Make up solution in sink, bath, or tank.  Use warm water to aid cleaning.   Add racks and submerse in Hydra ZX-100 solution for 2-4 hours depending upon degree of contamination.  Drain solution to chemical waste and lift rack and allow to drain.  Rinse thoroughly with fresh water turning rollers. Inspect racks.  Remove any stubborn deposits with a non-abrasive cloth or small soft brush (nail brush) and rinse off under pressure if possible.  If cleaning soft rollers extra rinse until clean.  Rinse solutions can go straight to drain. Processor Deep Clean leaving Racks in Machine Dilute Hydra ZX-100 at 1:15  with water 1. Empty processing chemicals into chemical waste tank and rinse through. Fill machine with water and add  ZX-100 as above. 2. Switch machine on to circulate ZX-100 through system inc pipe-work, re-circulation pump and heat exchanger.  3. When machine reaches operating temperature switch off and soak racks for between 2-4 hours.  4. When racks are clean, drain contaminated ZX-100 solution into chemical waste tank.  5. Re-fill tanks with fresh water and switch processor on to circulate rinsing water.  6. Drain and Repeat rinsing until water is clear.  Once water is running clear remove racks for inspection.  Remove          any stubborn deposits with non-abrasive cloth or small soft brush. 7.    Rinse tank to ensure all deposits are rinsed out of tank.  7. Rinse racks thoroughly with fresh water under pressure if possible turning racks to ensure clean rollers. For soft rollers extra rinsing is advised.                                                                                                                                                                                                                Mini Labs & Pro Labs/04/2008 Material Safety Data Sheet   All the information on this sheet relates to the concentrated product only, in use dilution will decrease any possible hazard significantly. Manufacturer           Hydra International Corporation Inc The Pinnacle Building, 3455 Peachtree Road NE, Suite 500, Atlanta GA30326, USA Tel: 1-866 809 7286       Fax: 1-866 379 1229  E-mail:  sales@hydra-usa.com Web Site: www.hydra-usa.com 1. IDENTIFICATION ZX-100 2. HAZARDS IDENTIFICATION Corrosive 3. COMPOSITION An aqueous blend of Sodium Hydroxide, Sodium Salt of Nitrilo Acetic Acid, Non-ionic Surfactant and dye 4. FIRST AID MEASURES EYES Flush with copious amounts of water and seek medical advice SKIN Wash with soap and water INHALATION Not applicable INGESTION In the unlikely event of ingestion seek medical aid immediately Give nothing by mouth to an unconscious person 5. FIRE HAZARD & FIRE FIGHTING PROCEDURES Non flammable 6. ACCIDENTAL RELEASE MEASURES SMALL SPILLS Wash away with water LARGE SPILLS Cover with sand and earth.  Pickup and hold for waste disposal 7. HANDLING AND STORAGE Closed containers above 5 oC 8. EXPOSURE CONTROLS AND PERSONAL PROTECTION RESPIRATORY PROTECTION Not applicable VENTILATION Not applicable PROTECTIVE GLOVES Wear PVC or Rubber Gloves EYE PROTECTION Wear goggles OCCUPATIONAL EXPOSURE LIMIT Not applicable 9. PHYSICAL AND CHEMICAL PROPERTIES PHYSICAL STATE Liquid COLOUR Amber ODOUR Alkaline FLASHPOINT Non Flammable SOLUBILITY Water Soluble SPECIFIC GRAVITY 1.364 + -0.01 @ 20 oC 10. STABILITY & REACTIVITY DATA CHEMICAL REACTIVITY Reacts as an Alkali STORAGE STABILITY Stable INCOMPATIBILITY Acids and Acidic Material HAZARDOUS DECOMPOSITION None AND COMBUSTION PRODUCTS 11. TOXICOLOGICAL INFORMATION EYES Corrosive SKIN Corrosive INHALATION Not applicable INGESTION Harmful/Corrosive 12. ECOLOGICAL INFORMATION Not classified as dangerous to the environment  13. DISPOSAL CONSIDERATION As per current rules of local authority 14. TRANSPORTATION INFORMATION Contains Sodium Hydroxide.        Corrosive.       Packing Group II        UN 1824 15. REGULATORY INFORMATION                                                          RISK PHRASES                                                                                  SAFETY PHRASES                                                         HAZARD SYMBOL LABELLING INFORMATION Contains 32% Sodium Hydroxide R35 Causes Severe Burns S2 Keep out of reach of children S24/25 Avoid contact with skin and eyes S26 In case of contact with eyes rinse immediately with plenty of water and seek medical advice S27                Take off immediately all contaminated clothing S36/37/39 Wear suitable protective clothing, gloves and eye/face protection S45 In case of accident or if you feel unwell seek medical advice immediately, Show product label Corrosive 16. OTHER INFORMATION 20 February 2008 The information contained in this document is provided in accordance with the requirements of Chemicals (Hazard Information & Packing) Regulations.  The product should not be used for any purpose other than as stated on the label without obtaining specific written instructions directly from the supplier’s Head Office.  As specific conditions of use are outside the sup- plier’s control the user is responsible for ensuring the requirements of relevant legislation are complied with.  The user assumes all liability for damage or injury caused from abnormal use, failure to follow recommended practices & any hazard inherent in the nature of the product.